Hero

Upgrading your interior lights to LED helps bring the interior out of the stone age. We now have a wide variety of options to help convert your interior lights to LED. Unfortunately we have not completed our LED packages for vehicles as yet so we have set up this guide to help you through the process. As always if you find yourself getting stuck at any point feel free to call us Monday to Friday 9:00am - 4:00pm on (03) 9369 8845.

Note that we will have a large range of pre-selectable kits available for specific vehicles in the future. 

INTERIOR LIGHTS

We are currently in the process with creating LED conversion kits specific to a wide range of makes and models but this does require a lot of research into all the individual globes fitted around the inside of each vehicle. In the mean time we are adding all the information required to convert to LED in our current available range which will expand as we come across different models requiring different globes, BA9s for example which is also a common parker globe.

Listed below are the current LED upgrades available at this stage,

LED GLOBE TYPES

T10 WEDGE

Starting off with most commonly found across the board is the T10. Used in most lighting throughout the interior of your car from dome/map globes to trunk and courtesy lights. Currently available in 3 sizes dependent on application the T10 comes in 33mm, 28mm and 24mm. All have a standard 8.8mm width at the plug end as the fitting is standard.

When replacing these types of globe our STEDI T10s are compatible with all T10 Wedge sockets you will just need to measure the height for the intended fitting via the previous globe. It is important to get the right size globe to replace your old ones as the wrong size may not fit into the existing socket and may have performance issues. You will find that 28mm T10's will suit 98% of vehicle parker lights and 24mm will be suitable to use in DRLs.

T10sT10sT10s

T5 WEDGE

Found more commonly used for only interior use is the T5 (2721) globe. The type of applications include gauge dashboard, instrumental plate, interior lighting and in some cases licence plate lights.

t5t5t5

T20 WEDGE

The T20 isn't very common when it comes to interior lighting but some specific models are fitted up with them. If these style of globes are installed in your vehicle they are mostly found in the dome light and the 2 map lights. T20 bulbs also have 2 different types, 1 being single filament (7440) and the other being dual filament (7443). The difference is that the single filament is used for applications with only a single illumination option i.e no dimmer. The dual filament is cross compatible with both 7440 & 7443 fittings. The 7443 can be used on aplications such as DRLs and brake lights where there is more than one level of brightness required from the globe. For example most DRL's will dim as the indicator is active as well as rear break lights that also have 2 levels of brightness, one for driving at night and one when the brakes are being applied.

t20T20 Example next to halogenHalogen Parker & DRL Toyota Hilux RevoLED T20 Parker / DRL Toyota Hilux RevoToyota Hilux Revo fitted with DRL and LED parker

FESTOON GLOBE

This style of globe is very similar to its usage as the T10 globe. Again available in 3 sizes, 31mm, 36mm and 42mm. The system in which Festoon globes is via 2 prongs each end in which the globe slots into. The Festoon globes are similar to the T10 application but dependent on the fitting style that your vehicle uses. 

These globes are measured end to end but are compatible within 2mm longer or shorter due to the style in which they are fitted into the socket.

festoonfestoonfestoon


BAYONET GLOBES

The bayonet type globes run 2 most common sizes that are found in vehicle parker lights and interior, BA9s & BA15s. These type of globes run various different connector pin patterns which is why we have added as much information below to help you find the exact replacement suited to your vehicle. What we mean by this is the 2 little tabs either side of the base that the light connects to the socket by running either parrallel or on an offset of height or symetry.


BA15S / BA15D

Our BA15 Globes are available in 2 varients at this stage the difference being the BA15S which is a single filament usually found in reverse lights or parkers and the BA15D that is a dual filament and used for brake lights or other dimable applications where there is a full brightness and a dimmed brightness. The BA15S globe runs a directly parrallel tab mount if you look at the 2 mounting tabs they will both sine up vertically and horizontally. The BA15D is slightly offset with one side being slightly higher than the other.

ba15Ba15Ba

BA9S

Common application for BA9s globes include map/dome lighting, dashboard lights, footwell, gauges, vanity & instrument clusters. The fitting pins run parrallel to one another which will slide into the mount and twist to lock into position.

BA9SBA9SBA9S

T5 LEDs:
T5

T10 LEDs:
24mm  /  28mm

T20 LEDs:
T20 Single Filament  /  T20 Dual Filament

BA9S LEDs:
BA9S

BA15 LEDs:
BA15S  /  BA15D

Festoon LEDs:
31mm  /  36mm  /  42mm

Bulk Builder:
Interior LED Kit Builder

HOW DO I KNOW WHAT GLOBES I NEED?

IDENTIFIYING GLOBE TYPE

Throughout your vehicles interior there are many different globe fittings required. Commonly found are the T10/T20 Wedge, Festoon and Bayonet globes. Replacing your interior globes are generally a straight up swap with existing globes but if you come to finding yourself stuck and are unsure of the globe type you need, below are listed the various types of interior light you may come across.


FootWell
Dome
Footwell
Boot

GLOVE BOX