CONTENTS

Divider

TOYOTA FORTUNER LED CONVERSION KITS

The Crusade is fitted with Bi-LED headlight but leaves the rest of the car in the dark. Read through this guide for our LED interior conversion on your 2017 - 2018 Toyota Fortuner Crusade with LED Headlights + Fog light upgrades for the GX and GXL models. The complete inside, as well as reverse lights & number plate lights, are fitted factory with halogen globes, easy enough these can be converted to LED for a pure white illumination inside with brighter reversing lights. Through our Toyota Vehicle Conversion, we have taken all the hard work out of finding all the globes throughout the vehicle so all you need to do is fit.

Shop LED Upgrades for VW Amarok

Divider

FORTUNER MAP LIGHT LED CONVERSION

Very much the same as all late model Toyota's, there is a slight modification that requires a slight shave to the bulb holders where you will need to shave the tops of the plastic tabs inside the holder next to the connection points just to allow the CANBUS to pass through. This will not reduce any compatibility with factory globes.

Fortuner Factory Halogen Map LightToyota Bulb Holder ModificationFortuner LED Map Light Upgrade

Divider

FORTUNER VANITY LIGHT LED CONVERSION

The vanity tab has a simple tab that is located on the outer side that you will just need to push in which will dislodge from the visor and pull down. Further to that, you can un-clip the bulb holder from the unit for easy access to the bulb. 

Toyota Fortuner Vanity Halogen GlobeVanity Light InstallFortuner LED Vanity Light

Divider

FORTUNER COURTESY LIGHT LED CONVERSION

Very much the same system as the vanity lights, though you will need to remove the lower part of the door trim to pop out the unit. Unplug the housing from the car because these are constantly triggered whilst the door is open. There is a small button to the back of the door frame that you can tape down to avoid the lights from activating whilst you are doing the conversion.

Fortuner Factory Halogen Courtesy LightFortuner Factory Halogen Courtesy LightFortuner Door Trigger Courtesy Light

Once removed the rest of the install is like any other, just out with the old and in with the new. As you can see from the last photo the increase in brightness is quite substantial. This is amplified at night with illumination of the surface surrounding the car.

Fortuner LED Courtesy LightFortuner LED Courtesy LightFortuner Halogen vs LED Courtesy Light

Divider

FORTUNER DOME/TRUNK LIGHT LED UPGRADE

Both the dome lights in the rear passenger and trunk are the exact same housing. These can be removed completely via the 2 tabs located diagonally from one another. 

Fortuner Factory Halogen Dome Trunk LightFortuner Factory Halogen Dome Trunk LightFortuner Factory Halogen Dome Trunk Light

Divider

FORTUNER GX + GXL LED HEADLIGHT UPGRADE | LOW BEAM

Toyota Fortuner models in the GX & GXL range are both kitted with projector headlights but halogen globes from factory. Our new Project Series LED Conversion kits to offer a wider field of vision below the cut off the line with an increase of brightness reducing the lights hotspot.

Toyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight Upgrade

Half Divider

To start you will want to remove the existing factory globe which can all be accessed easy enough through the back of the headlight with just enough space between the airbox to work within. Simply pug in the new LED globe and secure back into the headlight.

Toyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight Upgrade

Half Divider

While in this area it is also quite simple to upgrade the parker globes to LED as well. Simply pull the holder out, switch over the globes and refit into the housing. 

Toyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight Upgrade

Half Divider

As you can see from the below pictures, you now have a much cleaner look to the front end as well as a significant improvement out of the vehicle's headlight. The left side shows the factory halogen and lack of illumination towards the bottom of the beam. The right shows the new Project LED and an increase of all-round illumination.

Toyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight Upgrade

Divider

FORTUNER GX + GXL LED HEADLIGHT UPGRADE | HIGH BEAM

Toyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight UpgradeToyota Fortuner GX & GXL LED Headlight Upgrade

Divider

FORTUNER REVERSE LIGHT LED UPGRADE

The tail light needs to be removed to install the LED bulb, 2 bolts on the inside of the tailgate lock the housing in position. The housing removes towards the back with a bit of muscle and the bulb for the reverse light is located in the lower bulb holder.

Fortuner Reverse Light LED UpgradeFortuner Reverse Light LED UpgradeFortuner Reverse Light LED Upgrade

Divider

HIGH OUTPUT 1000 LUMEN LED REVERSE LIGHT

New to our range of LED conversion kits are the 1000 lumen high output globes. Available in T10/15, T20 and BA15S they will suit just about any car on the market. Compared to our other conversion globes they offer a much brighter illumination with a slightly different installation method. A good customer has thrown together a short video briefly describing the installation as well as giving quite a useful comparison between the factory halogen globes.

Divider

FORTUNER LICENCE PLATE LED UPGRADE

One of the more difficult conversions on the Fortuner is the license plate bulb. Tight to get to due to the strip that covers them only giving you minuscule access to remove. You will need to insert a flathead screwdriver through the side of the holder and twist slightly to pop out the holder. This is difficult due to the small amount of space you have to work with. These can be quite fragile as well so be a tad cautious whilst removing. Putting the unit back in is a lot easier than the removal process.

Fortuner Number Plate Light LED ConversionFortuner Number Plate Light LED ConversionFortuner Number Plate Light LED Conversion

Divider

CRUSADE AUXILIARY LED

Last but certainly not least this customer's Crusade is fitted with our 7inch Type-X LED Driving Lights. Coupled with the Rhino 4x4 bull-bar we think that this Crusade has some serious street cred'!. 

Toyota Fortuner STEDI Type X V1 7 Inch Driving LightsToyota Fortuner STEDI Type X V1 7 Inch Driving LightsToyota Fortuner STEDI Type X V1 7 Inch Driving Lights

Divider

TOYOTA FORTUNER PIGGY BACK ADAPTER

Toyota Fortuner High Beam Piggy Back Adapter

Our growing range of vehicle-specific piggy back adaptors now includes an adapter for the new Toyota Fortuner. This now brings the Fortuner back to a simple plug & play solution removing any hassle from picking up a high beam trigger.

Please Note: This is only compatible with LED Headlight models.

Shop Now

Divider

OEM TYPE PUSH BUTTON SWITCHES

The Toyota Fortuner, very similar to that of the Hilux will run the Short Type Toyota push button switches from the year 2016 onwards.

Toyota Fortuner Push Button Switches

Short Toyota Push Button Switch - Air CompressorShort Toyota Push Button Switch - Auxiliary BatteryShort Toyota Push Button Switch - BeaconShort Toyota Push Button Switch - Fog LightShort Toyota Push Button Switch - Front DiffShort Toyota Push Button Switch - Rear DiffShort Toyota Push Button Switch - Portable FridgeShort Toyota Push Button Switch - Left Side LightShort Toyota Push Button Switch - Right Side LightShort Toyota Push Button Switch - LED Light BarShort Toyota Push Button Switch - On OffShort Toyota Push Button Switch - Roof LightsShort Toyota Push Button Switch - Rear LightsShort Toyota Push Button Switch - Spot LightsShort Toyota Push Button Switch - STEDI UniversalShort Toyota Push Button Switch - Winch

Shop Now

Short Toyota Push Switch Wiring Diagram

1. Earth / Ground (Black on STEDI Harness).

2. Normally connected to the dash light circuit to be on when the dash lights are active.

3. Connect to your relay or accessories (Blue on STEDI Harness).

4. Connect from your source with an inline fuse (White on STEDI Harness).

WARNING: Always wire switch through a fused relay.