Ford Ranger Raptor LED Upgrade Guide
FORD RANGER RAPTOR LED BULBS
The new Ranger Raptor comes fitted with a factory LED Low beam and High beam whereas the earlier model had HID Low beam as standard, but remains the same dull, yellow halogen high beam. The high beam upgrade to LED will not only see a huge increase in light volume and lux but will also more closely match the color temperature of the factory-equipped HID low beam. This as well as many other LED upgrades for the Ford Ranger Raptor can be found via the Vehicle Selector below.
RANGER RAPTOR | LED HIGH BEAM UPGRADE
Upgrading the high beam on the Raptor is a straightforward process; the only difficulty you will encounter is negotiating your way through a tight engine bay. As you can see from the photos below the factory halogen high beam achieved a peak intensity of 4,279 Lux. Once swapped to our Copper Head LED upgrade we were able to achieve a massive gain of 7,702 Lux which is an 80% increase in peak intensity.
NOTE: The LED High Beam will not suit Bi-LED models.
RANGER RAPTOR | LED PUDDLE LIGHT ASSEMBLY
The LED Puddle Light upgrade for the Ranger Raptor follows the exact same process as the Wildtrak and XLT models. Slip a flat head screwdriver into the tabs situated on each side of the light to remove the unit. Unplug both the positive and negative wires to the factory light. Our puddle light upgrade uses the same method for installation, we took the extra precaution of applying electrical tape around the positive wire to prevent the cables from crossing when fitted back inside the mirror.
RANGER RAPTOR | LED LICENSE PLATE LIGHT ASSEMBLY
With the option to upgrade the globes inside the OEM license plate housing, we also offer a complete drop-in replacement that offers a smoother beam reducing glare in reversing cameras with easy installation.
RANGER RAPTOR | 1000 LUMEN REVERSE LIGHT LED UPGRADE
An easy yet powerful upgrade for the Ranger Raptor is the 1000 lumen LED reverse light. Plug & Play out of the box with an installation time shorter than 5 minutes, this upgrade will provide a dramatic increase of light over the factory halogen globes.
RANGER RAPTOR | UPPER GRILLE LIGHT MOUNT BRACKET
Designed to fit Ford Ranger Raptor (2019+).
Manufactured with 3mm Stainless Steel, and designed to be fastened to pre-existing holes which are already present on the inner side of the front grille. This is a completely non-intrusive install meaning that no new holes need to be made, nor will any section of the front bumper require any cutting or modifying. The end result is a very robust, stealth installation.
Design is optimized to suit our STEDI ST3K 21.5" or STEDI ST1K 21.5" LED Light Bars.
RANGER RAPTOR | LOWER GRILLE LIGHT MOUNT BRACKET
Suitable for the Ford Ranger Raptor (2019+), the lower grille bracket offers the ability to mount auxiliary driving lights without the need for an aftermarket bullbar. With easy installation and next to no modifications, this bracket will support either the 21 inch ST1K or ST3K LED light bars to offer performance lighting with a sleek, minimal fitment.
NOTE: This bracket will only work for the Ranger Raptor factory bumper.
RANGER RAPTOR | HIGH BEAM ADAPTOR
Our new piggyback adaptor specific for the Ford Ranger and Everest PXII/PXIII will remove any hassle from the installation of any of our driving light harness kits.
RANGER RAPTOR | SWITCH FASCIA PANEL
The Ford Ranger, Ranger Raptor and, Everest (2015-current) present limitations for switches when using additional accessories; whether it be auxiliary driving lights, winches, and so on. We now offer our switch fascia which is compatible with the above-listed models that will offer the ability to run 4 of our square-type push button switches. Expect OEM-like fitment and under 1 minute for installation of the panel itself.
NOTE: The switches used in the Fascia panel are the Square type Toyota Push Button switches.
RANGER RAPTOR | 'RALLY' NUDGE BAR
Our new STEDI Rally Bar is the re-imagining of the Ford Ranger Nudge Bar. Featuring a large 63mm diameter, ergonomically designed tube made out of durable 2mm stainless steel, this lightweight nudge bar can securely hold up to 30kg without any compromise. Designed for a seamless fully reversible and non-intrusive install (grill dependent), the Rally Bar provides a higher mounting position than the factory counterpart, not to mention the optimal setup for a killer lighting combination.
The STEDI Rally Bar is also a perfect match for our 60mm - 66mm HEX Bull Bar Tube Mounting Brackets. The Hex is designed to reduce excessive mounting equipment, and when partnered with the Rally Bar, provides the perfect solution for hosting your ideal light combination on your Ford Ranger.